hamza7
New member
Okay guys this was a detail carried out for my friend and a forum I recently just got sponsorship rights to.
This car had 18 layers of AG-HD on it so after 3 consecutive dawn washes, 1 overspray of AG CWC, Wolf's Deironizer, Elevated DeTARminator and medium and aggressive clay bar. I decided to polish the protection off, this car would survive a nuclear attack.
All of the correction was done on my Maki, with either a LC or Uber polishing pad and combination of M205 and Presta UCCL
I was ungroomed on this occasion, I will get a hair cut and shave next time I do a job
I explain a lot of stuff to them so feel free just to picture look
Justin’s dad watching us work
Authentic Merino wool wash-mitt FTW, only the best for my clients
Using a deironizing gel, to remove the iron particles stuck on Justin’s car. Remember this statement I’ll bring it up again
I use a sponge to spread it around, before that though. I use a box cutter to grit lines into it. So that dirt particles that may still be present can sucked into their instead of rubbing onto the paint. Detailing on the cheap 101
Spreading the gel around
Deironized
Here I sprayed some tar remover, I mean industrial strength tar remover. So I wear a respiratory mask for safety.
After that I use clay and clay lube to do a final decontamination on the car for what ever is left.
You just have to gently glide it over the surface, GENTLY!
“Huh, did you say something. Okay back to work”
My Boi is impressed with the shine already, what more can I do to impress him?
Trying to play doctor doctor (taking paint measurements of the car, you know how MUCH paint a Mazda has right)
Polishing prep finally!
Justin takes care of his car, so it was in good condition which means it’s very hard to take the pictures of defects.
Also it was impossible to get a 50:50 shot, here are a few attempts though.
This is the polish side, the right side
Un-polished side, do you guys notice the difference.
Here’s the polished side again
Ohh wait, here’s a good one.
Here’s the side of the hood, yes only a Mazda can we have a “side” of the hood. Damn sharp corners
The eyebrows, because the smiley face wasn’t enough
I took a break polishing, Loose Cannon wanted to rinse his car. Pfff Rinse, we detail here Bay Bee
This car had 18 layers of AG-HD on it so after 3 consecutive dawn washes, 1 overspray of AG CWC, Wolf's Deironizer, Elevated DeTARminator and medium and aggressive clay bar. I decided to polish the protection off, this car would survive a nuclear attack.
All of the correction was done on my Maki, with either a LC or Uber polishing pad and combination of M205 and Presta UCCL
I was ungroomed on this occasion, I will get a hair cut and shave next time I do a job
I explain a lot of stuff to them so feel free just to picture look
Justin’s dad watching us work
Authentic Merino wool wash-mitt FTW, only the best for my clients
Using a deironizing gel, to remove the iron particles stuck on Justin’s car. Remember this statement I’ll bring it up again
I use a sponge to spread it around, before that though. I use a box cutter to grit lines into it. So that dirt particles that may still be present can sucked into their instead of rubbing onto the paint. Detailing on the cheap 101
Spreading the gel around
Deironized
Here I sprayed some tar remover, I mean industrial strength tar remover. So I wear a respiratory mask for safety.
After that I use clay and clay lube to do a final decontamination on the car for what ever is left.
You just have to gently glide it over the surface, GENTLY!
“Huh, did you say something. Okay back to work”
My Boi is impressed with the shine already, what more can I do to impress him?
Trying to play doctor doctor (taking paint measurements of the car, you know how MUCH paint a Mazda has right)
Polishing prep finally!
Justin takes care of his car, so it was in good condition which means it’s very hard to take the pictures of defects.
Also it was impossible to get a 50:50 shot, here are a few attempts though.
This is the polish side, the right side
Un-polished side, do you guys notice the difference.
Here’s the polished side again
Ohh wait, here’s a good one.
Here’s the side of the hood, yes only a Mazda can we have a “side” of the hood. Damn sharp corners
The eyebrows, because the smiley face wasn’t enough
I took a break polishing, Loose Cannon wanted to rinse his car. Pfff Rinse, we detail here Bay Bee
