should i prime surbuf pads?

J

jeffny09

New member
was wondering whats the best way to go with these pads...if i need to prime them first or not...thanks..and if theres any special technique with them as well

thanks
jeff
 
jeffny09 said:
was wondering whats the best way to go with these pads...if i need to prime them first or not...thanks..and if theres any special technique with them as well

thanks
jeff
Click to expand...

Hi Jeff, thanks for posting this to the forum!

For maximum performance with the Surbuf pads there are a couple of things that will work best, in my experience.

  • Use them with a non-diminishing abrasives compound such as Meguiar's M105, M86 (So1o), or Optimum Hyper Compound Spray.
  • Prime the pads on first use by adding product to the face of the pad and spreading with your thumbs. Add more product to cover the bare spots. Allow the pad to sit for 5-10 minutes. Then clean the pad with compressed air or a nylon pad brush such as the Pad Reconditioning Brush.
  • Unlike other pads, which require some pressure, you want to let the fibers of the surbuf whisk across the paint. When using 6.5 inch or larger pads the weight of the machine will be sufficient. When using 5.5 inch pads you may need to lift slightly. Because there is no pressure you want to use speed 4 or 5 to avoid excessive pad rotation which will pull the fingers outward (centrifugal force) and cause them to lay flat.
  • Clean the pad after EVERY section, again by pad brush or compressed air. Once you have primed the pad (first step) you only need to add three small drops of product for each additional section.
  • When the pads become saturated and matted it is time to switch to a fresh pad until the previous can be washed and dried.
  • Keep in mind that the Surbuf pads will leave a haze on the paint requiriing final polishing.
 
Todd Helme said:
Hi Jeff, thanks for posting this to the forum!

For maximum performance with the Surbuf pads there are a couple of things that will work best, in my experience.

  • Use them with a non-diminishing abrasives compound such as Meguiar's M105, M86 (So1o), or Optimum Hyper Compound Spray.
  • Prime the pads on first use by adding product to the face of the pad and spreading with your thumbs. Add more product to cover the bare spots. Allow the pad to sit for 5-10 minutes. Then clean the pad with compressed air or a nylon pad brush such as the Pad Reconditioning Brush.
  • Unlike other pads, which require some pressure, you want to let the fibers of the surbuf whisk across the paint. When using 6.5 inch or larger pads the weight of the machine will be sufficient. When using 5.5 inch pads you may need to lift slightly. Because there is no pressure you want to use speed 4 or 5 to avoid excessive pad rotation which will pull the fingers outward (centrifugal force) and cause them to lay flat.
  • Clean the pad after EVERY section, again by pad brush or compressed air. Once you have primed the pad (first step) you only need to add three small drops of product for each additional section.
  • When the pads become saturated and matted it is time to switch to a fresh pad until the previous can be washed and dried.
  • Keep in mind that the Surbuf pads will leave a haze on the paint requiriing final polishing.
Click to expand...

thanks todd. appreciate the answer..i didnt know most od that stuff..and will come in handy! :thumbup:
 
It has been my expierence that the 6.5's perform the best. Actually it was Kevin "SurbufDaddy" Brown who recommended this to me, and as usual he was spot on

Todd has a very nice article on these also but I can't find it at the moment

If you can spring for it get 6 pads and change them out instead of using air. If not, just be sure the hairs are as straight up as possible before proceeding
 
i have a backing plate..but it doesnt cover the whole pad for the 6.5..is there a bigger one..or will that plate be fine?
 
jeffny09 said:
i have a backing plate..but it doesnt cover the whole pad for the 6.5..is there a bigger one..or will that plate be fine?
Click to expand...

You want the backing plate to cover as much of the pad as possible with a small lip for safety. If you use a 5 inch backing plate on a 6.5 inch Surbuff, you are only using 5 inches of the Surbuff.
 
Todd Helme said:
You want the backing plate to cover as much of the pad as possible with a small lip for safety. If you use a 5 inch backing plate on a 6.5 inch Surbuff, you are only using 5 inches of the Surbuff.
Click to expand...

thanks todd. ima order the plate from u guys tonite..
 
You must log in or register to reply here.
Back
Top