need a good torque wrench

hondaguy2582

hondaguy2582

New member
already searched, but i want to know what torque wrenches are a good buy. i don't want to spend over a 100 bucks for a torque wrench, but i want a good quality, middle of the road, torque wrench that will last me for a few years. I figure since i do all my maintenance on my honda at home im eventually going to need one for doing the spark plugs, rotating the wheels and such. Anyone know good deals and what models to buy?:nixweiss
 
Craftsman has reasonably priced torque wrenches that are pretty accurate. Just remember after you use any torque wrench to reset it back to zero.



Regards,
 
I would go with a Craftsman. There are better wrenches on the market however for the price Craftsman is hard to beat plus anytime I buy a torque wrench I would only want a new one because so many things can cause them to mess up. That is unless you buy a used one then have it tested and calibrated.
 
I've not had good expierences with Craftsman Torque wrenches. I'd look on eBay for a used Snap-On or Mac wrench. You can find some lighly used models for under $100. Watch the prices on the Snap-On stuff, they seem to draw trolls that love to run up bids. Armstrong and Proto also are not bad, but not as nice as a Snap-On or Mac. Oh, SK isn't bad either. :)



I'd go with the 3/8''s drive. In many cases the 1/2'' is just too big to get into cramped areas. Get a cheapo 1/2'' for torquing lug nuts.



:up :up
 
yeah, the only problem with buying on ebay is that you don't know what abuse its been through, and if its even calibrated right. the snap-on looks pretty good, although, id want to spend 90 bucks tops for a used click type.
 
I've had good luck buying used snapon ratchets and sockets on ebay (not the same as a torque wrench I know). You do have to watch what is listed, and ask lots of questions, and watch for poor ratings, and make sure you don't go above your set price.



But so far, I've been able to get most stuff at 50-60% of original price for stuff that has been barely used.
 
Harbor Freight; Craftsman are fine but they still sell the same one I bought 25 years ago that has the "window" showing ft-lbs, etc. Over time that fogs and makes it hard to see the setting--works fine but...
 
I would suggest getting a Snap-on like this one: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=2332880836&category=42265



or



http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=2332866402&category=20774





I have found the slight movement in the flex head design very useful. Additionally the lever/turn dial for setting the torque is great and if you forget to turn it back to zero it is not suppose to effect the calibration. If you get it used have it tested and calibrated by your local Snap-on dealer. There are always some of these on Ebay.



Another thought on torque wrenches. Get more than one. I say this because the wider the range the less accurate it is at the ends of the range, especially at the low end. Get one for lighter settings something like 5-75 lbs. in a 3/8 drive and then another for heavier stuff, something like a 40-250 lbs. ½ drive.
 
I've had my 1/2 drive MAC torque wrench for 15 years and it has served me well.



I would have prefered the Snap-on one but at the time e-bay didn't exist and I didn't have the extra $$.
 
i've been putting off getting some torque wrenches for a while now. Harbor freight? What brands do they carry?

I need a wrench for my wheels, 80 lbs., and a lower one for other stuff (~25 lbs.).





bet993, where did you find a 5-75?
 
I'd like to think I'm a little qualified to answer this question...I have 9 torque wrenches and about $45k of tools sitting in the basement and garage (being an ex-technician of 7+ years helped acquire a few tools).



While the quality of a Snap-On, Mac or Matco tool is generally higher than consumer-grade tools, I would not recommend buying a Snap-On, Mac or Matco torque wrench via eBay.



The chances of it being out of calibration are simply too great, and to have the wrenches calibrated costs over $100.



For my weekend projects, I use a Craftsman torque wrench. I have the 20-120lb model, 1/2" drive and I have a 3/8" drive model as well. Both are close enough for the weekend warrior and will withstand weekend-type work loads. I use them for torquing wheel lug nuts, and things like that - works perfectly.



If you were a pro-wrench and were using your torque wrench every day, or were torquing critical components like bearing caps and transmission components, then I'd say to get the Snap-On, Mac or Matco. But for things like lug nut torque, brake caliper torque, etc., the Craftsman will be more than adequate.



Oh, and one last thing - many newer cars have "stretch to torque" values. You torque the fastener to a certain value, then you use an angle guage to torque it a certain # of degrees past the first torque value...it stretches the bolt. :)
 
I have a Craftsman 1/2" drive torque wrench just like Steve's. I agree completely - for a shadetree mechanic a Craftsman is excellent. A pro quality wrench is best if you rebuild motors or something but beyond that, they're overkill.



I also have a Husky 3/8" drive wrench in inch pounds. I find I use that one often for work on lawnmowers or other small engine equipt. There are gonna be times you need a wrench that can torque to a spec under 25 ft lbs so an inch lb wrench is worth having. Again, no need to go off the hook for one. Mine cost me about $45.00 at Home Despot.
 
harbor freight carries some generic torque wrenches. I saw one there a few weeks ago, but I didn't like it much. It was really huge, which in this case is not a good thing. It wouldn't get into tight spaces.



It was really cheap though - about $40
 
bet993 said:
Another thought on torque wrenches. Get more than one. I say this because the wider the range the less accurate it is at the ends of the range, especially at the low end. Get one for lighter settings something like 5-75 lbs. in a 3/8 drive and then another for heavier stuff, something like a 40-250 lbs. ½ drive.
Click to expand...

I agree - and before you buy, check what range of torque settings you need. I know it sounds obvious but theres nothing more annoying than finding that your car has a need for a setting outside the range of the one you just bought
 
Can I borrow this thread while we are talking about tools. Impacts, well I have been using my old generic brand 1/2 inch drive impact for years but I often have to use a cheater pipe to break bolts lose. About two years ago I purchased the best craftman 1/2 drive impact they had. Even though it had great stats it really did not do any better at breaking lose bolts or nuts than my old impact, so I took the impact back to Sears. My compressor is a two horse 220 volt and I can pump it up to 120 foot lbs..



Does anyone have a recommendations on a 1/2 drive impact or is the problem with pressure.



Thanks for the response.
 
And still another Craftsman vote. I have their 1/2 in. drive micrometer-type set torque wrench. Heck! It's good enough for government work. :D
 
You must log in or register to reply here.
Back
Top