Finish Kare Compounds

B

blake_jl1

New member
I've been trying to find reviews on FK's compounds/polishes (360, 336NG, 330, 17) but haven't been successful.



Has anyone used these products? What are your thoughts/comparisons?



I've ordered a few of their other products (I'm in Australia) and wanted to add on a couple of things but stuffed if I can get in contact with them. I've emailed, called and left messages. It's driving me crazy!



Thanks
 
Blake,



I saw your post on DW, but because they directed you towards Autopia I answer (as I can) here.



Sooo, I've had a couple of problems with the FK polishes initially. Then I understod their working characteristics and never had a problem since.



360: very good medium duty compound with great finishing ability and good cut. Works OK with a DA machine. It is sensitive about a very thin buffing film, so spread it out evenly over the entire work area, and then start to work it.



330: light polish with concealers. Produces a fine finish, but it has a slight glazing effect.



17: fine polish which can be used as finishing polish. It has a bit more bite initially than expected (similar to 303 - yes corrective gaze), but finishes down very fine.



They have average working times, and you have to follow their descriptions to a T. If you do something wrong, they will *tell* you as they can spit their thickener (bentonite clay) from under the pad. They can gum up a bit in situations like this, but if you master them, they are cooperative and produce great results.



I haven't tried the 336NG unfortunately, but still plan to do...



If you can, order 215 from them; as it is one of the greatest AIOs on the market.
 
BigJimZ28 said:
you are thinking of 303



330 is a light polish
Click to expand...



Nope just talked with them at FK. 330 Mini Buff is supposed to have polymers and waxes that good for 60-75 days protection. Smelled just like Megs #7 to me.......or #80.
 
Yes, 330 is definitely more than a light polish. The numbers are confusing, because I'd called the light polish 330, and the specially enhanced formula 17. Unfortunately it's the other way around.



BTW, it's good to know their rating of the expected performance of the poly/wax package in the 330.
 
Bence said:
Yes, 330 is definitely more than a light polish. The numbers are confusing, because I'd called the light polish 330, and the specially enhanced formula 17. Unfortunately it's the other way around.



BTW, it's good to know their rating of the expected performance of the poly/wax package in the 330.
Click to expand...

Do you ever have any problems with 330 or 215 being applied with a PC/G110?

I used them on speed 5 and when I went to remove it, it was hard to get off and there were circles that looked like the pad. It eventually came off. Did I use to little/to much product or did I over buff?
 
I had issues with 360, but if you shake them really well and use the correct amounts, they will cooperate well. And keep in mind what I wrote above regarding a thin, even buffing film over the work area. Spread them at speed 4, work them at 6.
 
Bence - saw your comments...



had good success with FK1000, PW & 425 and have some 303 to try next. Any tips on using 303 with DA or rotary and exactly what it will deliver? I see it as a cleaner/light abrasive/glaze - is that right? Was thinking a 1 step before FK1000 etc?



cheers
 
Damon, the abrasive package is only an issue when you don't expect it and you work by hand.



Otherwise it breaks down in a few seconds and gives a nice surface. If you want a non-abrasive glaze, I'd suggest the #1 New Car Glaze. Interesting glaze as it cures and it likes to be topped next day. Very slick too.
 
thanks Bence - happy with the light abrasives and like to do these things by machine where possible, so not an issue. Will try it on the next detail...
 
tdekany said:
Jeff, that is the issue. You can't create enough heat. Always polish on speed 6. Also yse less product. You really don't need much.
Click to expand...

So, the more heat the better with FK? Also, less is best? I used a quarter sized amount on a primed 5.5 low pro LC Orange pad. So maybe a dime sized amount per panel???
 
Jett, a quarter sized blob is good for pad priming. But for each subsequent panel, use around 3-6 pea sized drops, depending on pad size and thickness. For your 5.5 low profile pads, I'd use 4-5 drops max.
 
Bence said:
Jett, a quarter sized blob is good for pad priming. But for each subsequent panel, use around 3-6 pea sized drops, depending on pad size and thickness. For your 5.5 low profile pads, I'd use 4-5 drops max.
Click to expand...



How would you work it with the G110? Speed six? Should I work until clear? How long should I wait before removing it?



Thanks!
 
You don't have to wait before you remove a polish as it doesn't contain protective ingredients which need to set and cure on the finish.



Yes, speed 6, until residue goes clear or starts to dust.
 
You must log in or register to reply here.
Back
Top