Few questions before I winter wax

D

danz24

New member
This will be my FINAL waxing/washing till next year spring. So everything will be for durability!



1. I plan to use do this: RMG then 3 layers of Collinite 476s. Is this fine, or is the RMG a useless step?



2. Is it necessary to clay, and do a light polish before I apply the wax? Or can I just wash the car and put the 3 layers of the 476s? I have some protection still as my car still beads, but the last wax I used was s100.



thanks :)
 
make sure you remove the previous wax. and also allow each coat of 476 to fully cure before apply next coat. atleast 12 hours between coats. but honestly 3 coats may be over doing it. this is from the collinite web site



Super Doublecoat Auto Wax (No. 476s)

One of the finest paste type auto waxes available. Easy to apply and absolutely DETERGENT PROOF. Collinite Super Doublecoat is guaranteed to outlast and outshine any other competitive auto wax, polish or protective coating under any conceivable condition. That's why it's called the PERMANENT AUTO WAX. No hard rubbing or buffing... and no special applicator is required. Collinite Super Doublecoat will last a full year, even under adverse conditions. Clear coat safe.
 
Cordially disagree with keepitclean. I contacted the Collinite people before I started using 476 a while back. They told me that a cure time of 45 minutes or so was fine before adding the next layer. I asked specifically about a 12 hour cure time and they said it wasn't necessary.



I have not had problems laying 476 on over other products, just put it on over DWG for winter.



As to how many coats you need, I suppose it depends on the severity of your winter conditions, whether or not your car is garaged or sits outside, etc. I put on 3 coats but we drive a lot in tough conditions, salt, sand, winter sludge. Two coats could be fine for less difficult conditions.
 
STSInNYC said:
Cordially disagree with keepitclean. I contacted the Collinite people before I started using 476 a while back. They told me that a cure time of 45 minutes or so was fine before adding the next layer. I asked specifically about a 12 hour cure time and they said it wasn't necessary.



I have not had problems laying 476 on over other products, just put it on over DWG for winter.



As to how many coats you need, I suppose it depends on the severity of your winter conditions, whether or not your car is garaged or sits outside, etc. I put on 3 coats but we drive a lot in tough conditions, salt, sand, winter sludge. Two coats could be fine for less difficult conditions.
Click to expand...



applying over a glaze or sealant is ok. but topping a different wax MIGHT cause bonding issues. as for the cure time if i layer i personally wait 12 hours to make sure it is fully cured. some waxes/sealants dont need that long. it is just how i do it. and since you asked them about a 12 hour cure time you and alot of us have heard the same thing. i have 1 layer of 845 on my car and it is holding up strong after 4 months already. and 476 has a longer durability
 
I went on what the Collinite people told me. A year ago, in October, I did three layers of 476, cure time 45-60 minutes between. In April the wax was beading water very nicely, despite a lot of exposure to rain, snow, salt, sand, general winter sludge.
 
K so my plan will be to wash car with dishwashing soap (to remove wax)

dry

then put 1 coat of collinite

wait 45min

put 2nd coat of colline

done :)



btw would putting a QD (meguiars ultimate quick detail) after I finish help increase its durability, it is it an unnecessary step?
 
I'd give it a quick claying. I'm pretty sure you'll find the clay does in fact clean off a fair amount of [stuff] that woulda otherwise been trapped under the wax. IT'll clean off any compromised wax artifiacts too (i.e., "dead wax" that the regular wash might not get).



Just do a quickie job while you wash, won't take but a few minutes.
 
did I read the thread wrong? I seem to believe that you are not washing your car to next spring... I hope that I was wrong for thinking that. Clean cars are the best! haha... Don't depend on just the wax. Best of luck to you!
 
I put 2 coats NXT 2.0 and 2 coats Mothers pure Canauba wax - with about 12-24 hours in between coats. I think i might put one or two more coats of the Carnauba.



Anyone else layer Canauba?



The Mothers stuff says it's pure so im assuming there are no cleaners in it.
 
93zder said:
I put 2 coats NXT 2.0 and 2 coats Mothers pure Canauba wax - with about 12-24 hours in between coats. I think i might put one or two more coats of the Carnauba.



Anyone else layer Canauba?



The Mothers stuff says it's pure so im assuming there are no cleaners in it.
Click to expand...



Ive been known to do 2 coats of Collinite
biggrin.gif
 
Premium said:
Mothers, LOL! You're better with just NXT 2.0
Click to expand...



Well i've had this bottle in my collection for a few years probably and i just wanted to use it up. But i was actually impressed with the shine and slick surface it left.



How come you dont like Mothers? I'm just curious - is this stuff that bad?
 
You must log in or register to reply here.
Back
Top