05 STi Correction

M

MasterBlaster

New member
Been haveing trouble posting even with 10+ posts. Seems like it had something to do with the thread title. Anways, this is my first correction on my '05 Obsidian Black Pearl STi



I did this in the begining of March. Just joined the site and wanted to post this. If anyone is a member over on IWSTI you probably seen it.



Bought the car last July with close to 38k on it. Paint was pretty rough, being black it looked even worse. By the time I got done taking care of some other stuff on the car it was winter, so I waited until the weather broke to take care of the paint.



I used a PC with Menzerna Super Intensive Polish on a Detailers Doamain Green pad, really bad spots I used an Orange pad, Followed up with PO85RD on a blue pad. Topped off with Einszett Glanz.



First up I cleaned the engine with some Adam's APC. Dressed with Adam's VRT and some Einszett Vinyl/Rubber Protectant.



Before

dirtyengine.jpg




After

engineclean.jpg




Some foam action

firstwash.jpg




Only clay pics that came out well. The real bad one was what it looked after each door. The other one was what it looked like on most other panels.

clay.jpg


doorclay.jpg




Passenger side rear door before

Swirls.jpg




50/50

50.jpg




Rear door done, front untouched

Half.jpg




Both doors done

Both.jpg




Passenger front fender

fenderbefore.jpg




50/50

fenderhalf.jpg




Passenger quarter before

quarterbefore.jpg




After

quarterafter.jpg




Spoiler side (sorry it's blurry)

spoilerbefore.jpg




After

spoilerafter.jpg




Trunk was really rough.

trunkbefore1.jpg


trunkbefore2.jpg




After

trunkafter1.jpg


trunkafter2.jpg




Some pillar before and afters

apbefore.jpg


apafter.jpg


cpbefore.jpg


cpafter.jpg




Water beading while washing to get all the dust off

bead2.jpg


bead1.jpg




And some finished pics, didn't have time to get any real nice ones

finished.jpg


finished4.jpg


finished3.jpg


finished2.jpg




I've always been a detail freak but this car sent me over the edge. Started lurking on here and reading up a lot and dove in head first. I'm pumped with how it turned out.



Looking forward to any thoughts/advice. :buffing:



Mike
 
Very very nice job !

Very good correction you got there!



This car is so nice!

It'll probably be my next purchase after my SRT4.



:ca
 
Thanks for all the comments!



Right now the car is "stage 2". With the reflash and turbo-back exhaust it's suppose to be ~359hp and ~385lb.-ft at the crank. Not a lot by many WRX guys but plenty to make me happy.



DetailnByDustn said:
Outstanding Job! Why do you use a foam gun does it clean better?
Click to expand...



I figure the more I can do to lessen the chance that I get swirls on the black the better. The foam is suppose to help loosen dirt and what not, before hand washing. I can say it makes washing the car much easier. The other day, I knew it was going to rain but, my car was pretty dirty. I rinsed it, sprayed some foam on, and rinsed after a few minutes. It almost looked as good as if I had really washed it. Right now I'm using Adam's Car Wash, mega foam and it smells good too.
 
Yeah I did a few here and there as I went, to make sure what I did was working (was my first correction). I think my IPA mixture was a little off actually. It seemed to want to dry up as soon as I took one swipe with a towel. If that makes any sense. I might invest in some "pre-made" IPA type stuff, maybe Top Inspection.
 
God damn, I've never seen clay look that disgusting before - what the hell did you do before hand? :rofl



Nice car though! Are those Enkei rims?
 
ZoomBoy said:
God damn, I've never seen clay look that disgusting before - what the hell did you do before hand? :rofl



Nice car though! Are those Enkei rims?
Click to expand...



LOL. That's whatever was left over from the previous owner and winter. If you think that was bad, here's a pic of some clay after doing the passenger side of my mother-in-laws car....



doorclay-1.jpg




Ah and my wheels are just Rotas. The previous owner really borked up the stock BBS wheels and the tires were shot. A guy was selling the Rotas with brand new tires for cheap so I bought them. I'm eventually getting Works or Advans.
 
wow that looks really good now.



quick q thou - see your DIRTY clay? would that be a throw out? or wash off and kneed?
 
You must log in or register to reply here.
Back
Top