Zaino curiosity

G

golfdude

New member
Here's my big question...is the Zaino line a substitute for traditional polishing (paint correction), or is it designed for paint protection (meaning you would still have to polish, but instead of using a glaze, sealant and then wax, you would use the Zaino line)? Thanks for the help.
 
If you are using a(n oily) glaze before a sealant, you are asking for trouble. The Zaino line contains a mild paint correction product (Z-PC), but the Zaino line is primarily a protectant one. If you are using a polish prior to Zaino that contains oils (like Meguiar's polishes) you will need to remove any oil residues before Zaino application.
 
ZaneO said:
ZPC Fusion is a mild paint cleaner/abrasive polish. Z5 Pro and Z2 Pro are sealants.
Click to expand...



That is correct. With that said though, The ZPC can really tackle some paint correction as seen below, and still finish perfect.





All done with ZPC via PC speed 6, orange light cut pad



mk1.jpg




mk4.jpg




Greg
 
ZPC has some really good initial bite. I had a couple of scratches on the side of my car, not too deep into the clear coat but way worse than swirls. I tried to get rid of them using ScratchX and they hardly budged. I hit them with ZPC and they were gone fast.
 
Setec Astronomy said:
If you are using a(n oily) glaze before a sealant, you are asking for trouble.
Click to expand...



Thank-you everyone for the comments. But, I must ask for more clarification of this topic. I might use glaze in two ways:



Polish, AIO, Glaze (RMG), then P21S or Collinite 476S



or



Polish, Glaze (RMG), Menzerna FMJ, Collinite 476S or P21S



Please tell me what is wrong, if anything, using these techniques, and how should I modify my techniques to use glaze more effectively without sacrificing it's durability.
 
Sealants may not last over a glaze as they can not bond as tightly to them. This is product dependent. If you use a more stable glaze like FK1 303, which can correct a little bit, you'll gain more durability but it won't fill too much. Glazes which are great fillers are better in conjunction with a (heavy) carnauba.
 
ZPC can remove up to 1500 grit sanding marks with the right pad and machine. That's fairly aggressive for a product that finishes so nicely.
 
Any other comments on my techniques or other suggested products to go over glaze to produce long-term protection??
 
GregCavi said:
That is correct. With that said though, The ZPC can really tackle some paint correction as seen below, and still finish perfect.





All done with ZPC via PC speed 6, orange light cut pad



mk1.jpg




mk4.jpg




Greg
Click to expand...

The lighting/angle of the picture has changed in the before and after frames and the shot is not as tight in the afters. I still see swirls in the lower light reflections (particularly the right side). Did this remove them or not? It doesn't appear to be the best example of what the product can do.
 
Gearhead- the lower panels get hit with the spot buff pads, which unfortunately had not been done at the time of the picture. I think the following set will help clear up any confusion.



mk2.jpg




mk3.jpg




Also take note that the left is after one pass, and the right has no polishing.



Greg
 
GregCavi said:
Gearhead- the lower panels get hit with the spot buff pads, which unfortunately had not been done at the time of the picture. I think the following set will help clear up any confusion.



mk2.jpg




mk3.jpg




Also take note that the left is after one pass, and the right has no polishing.



Greg
Click to expand...

Greg thanks for the clarification. I had never seen any of your work that I hadn't fully appreciated until this first set. I knew you had it in you.
 
You must log in or register to reply here.
Back
Top