Need help with CQuartsUK

[angryfx45]

I got my CQUK delivered.

I will be coating my car in few days. After alittle bit of correcting.

It will be about 60-70 degrees here in Nyc, indoor garage.

Steps
1 wash
2 clay lite
3 correct using m205 (did m105 cpl wks ago)
4 rinseless wash
5 50/50 ipa wipedown
6 coat

Any steps i missed out? Im new to coating

Also in that temp of 60 70f degrees
How long should i wait after i apply the coating b4 wipe down with suede towel?

Ive seen so many videos some wipe instant some wait cpl mins.

This is the part im confused about. Very new to coating.

Thank you!#
4





Sent from my SM-N900V using Tapatalk

 

[Ronkh]

Just my .02..... Instead of rinseless wash after the 205, I`d do a complete wash. When I did mine we actually foam bath then washed.......

 

[Ronkh]

http://www.autopia.org/forums/everything-else/45337-3-amigos-date.html?highlight=taping

 

[angryfx45]

Just my .02..... Instead of rinseless wash after the 205, I`d do a complete wash. When I did mine we actually foam bath then washed.......

I guess i meant waterless wash using garry dean method but with cpl drops of dawn soap.

But if i can get to proper washing i will thank you.(its an apt building indoor lot so i dont have access to water TT


Sent from my SM-N900V using Tapatalk

 

[Ronkh]

http://www.autopia.org/forums/the-d...r-fl-sun.html?highlight=old+guys+with+buffers

 

[Ronkh]

I guess i meant waterless wash using garry dean method but with cpl drops of dawn soap.

But if i can get to proper washing i will thank you.(its an apt building indoor lot so i dont have access to water TT


Sent from my SM-N900V using Tapatalk

Then waterless wash using poorboys spray and wipe to make sure no polymers or soap residue is left over.

 

[angryfx45]

http://www.autopia.org/forums/everything-else/45337-3-amigos-date.html?highlight=taping

thank you Ron.

So after the inital application how long should i wait before the wipe down?




Sent from my SM-N900V using Tapatalk

 

[Ronkh]

thank you Ron.

So after the inital application how long should i wait before the wipe down?




Sent from my SM-N900V using Tapatalk

Me, I would do it right away. My experience is completely different than yours though.

 

[angryfx45]

Me, I would do it right away. My experience is completely different than yours though.

Ok so i should do half hood about 2 criss cross motions and wipe with suede.

Upper door criss cross wipe and on to lower door etc etc

Sounds good?

Sent from my SM-N900V using Tapatalk

 

[Ronkh]

Ok so i should do half hood about 2 criss cross motions and wipe with suede.

Upper door criss cross wipe and on to lower door etc etc

Sounds good?

Sent from my SM-N900V using Tapatalk

I might break it down into 3 if large panels...

 

[angryfx45]

Great will post back on how it works

Sent from my SM-N900V using Tapatalk

 

[Rsurfer]

Great will post back on how it works

Sent from my SM-N900V using Tapatalk

Just remember when you are knocking down the high spots, don`t go crazy, you are not buffing off wax. If you only have one large suede towel, use a short nap MF towel for the initial wipe and use the suede for the final wipe down. It`s important to final wipe with a clean towel to prevent streaks.

 

[angryfx45]

Just remember when you are knocking down the high spots, don`t go crazy, you are not buffing off wax. If you only have one large suede towel, use a short nap MF towel for the initial wipe and use the suede for the final wipe down. It`s important to final wipe with a clean towel to prevent streaks.

Got yah thank you i think car pro kit came with a cple large ones but ill be soft

Sent from my SM-N900V using Tapatalk