Help on Porter Cable selection

R

rauljimenez

New member
Hello I've been reading a lot before I decided that I want to spend some more money into getting myself a machine, but I want to start out slowly since money is a bit tight atm.



is there a way I could start out with a craftman sander/polisher 6 inches pad. Thanks a lot for your help



Here is some quick reference to what it does along with a link provided :



This versatile 2-speed sander/polisher with a 4.5 amp motor is great for most sanding or polishing tasks. The trigger switch controls the two speeds and can be locked on for extended use. The tool's rear handle rotates 90 deg left or right and the side handle can be mounted on top, right or left side. A live tool indicator glows green to make the user aware of electrical current. Includes: rubber backing pad, wrench, polishing bonnet, spanner nut, aux handle assembly, and manual. Craftsman 2 Speed sander/polisher with 4.5 amp motor is great for most sanding or polishing tasks. The trigger switch controls the two speeds and can be locked-on for extended use. The tool's rear handle rotates 90 degrees and the side handle can be mounted on top, right, or left side. A spindle lock makes it easy to remove or install the rubber pad or spanner nut and a live tool indicator glows green to make the user aware of electrical current. Includes rubber backing pad, wrench, polishing bonnet, spanner nut, auxiliary handle assembly and manual.



* 4.5 amp motor - provides power for most all sanding and polishing needs.

* Two Speeds (1400 & 1650 RPM) - Lower speed for polishing; Higher speed for sanding

* Rear Twist Handle - rotates 90 deg with push of button for more comfort and control

* Spindle Lock w/pin provided - for ease of changing paper, pads, or bonnets

* The extended length, two finger switch w/lock-on - provides more control and comfort during extended use

* Auxiliary Handle - mounts left, right, or top for added control

* Ball and Sleeve Bearing - permanently lubricated for long service free life

* Live Tool Indicator - glows green to make user aware of current to tool
 

Attachments

  • 00911506000.jpg
    00911506000.jpg
    7.6 KB · Views: 11
Joshua thanks for such a fast response. I had seen that Machine you described above but I have 1 little nasty problem right now.... not a lot of money.



The rotary I put above is about 70 bucks which is fine right now for me because I need to get some pads of course.



My next question is, should I keep holding a bit of money and get myself a porter cable 7424 or the Ultimate Machine or can I go and try that one for 70 bucks??
 
I couldn't tell you how well that machine works, but based on the specs listed that is not similar to the PC. The PC is a dual action/ random orbital machine which makes it safer and easier for someone new to detailing to polish a car.



Considering your tight money situation at the moment (believe me, I know all too well how that feels!), I would save up the cash and get a new or used PC. It's a reliable and proven machine. From having regrets on previous purchases, I usually try to wait and buy the product I want, instead of buying something just as a substitute. In the end, it just ends up being more money wasted.



Keep in mind, I don't follow that rule every time, otherwise I'd be saving my whole life for a Ferrari and never have a car :) If the product you're looking to buy is at a reasonable, realistically acquirable cost then wait and save up for it. I hate buying or doing anything twice because I was too cheap the first time around.



Good luck!
 
You're welcome



I agree with BlackElantra, save up a little more for the UDM or Porter Cable 7424. You will be alot happier. Using a rotary requires a learning cure, one little mistake and you can burn through your paint.



If you have an ebay account for $30 more than your limit you can get a brand new 7424 from here



eBay Motors: Porter Cable 7424 6" Random Orbit Polisher Brand New (item 320135096758 end time Jul-15-07 13:21:41 PDT)



Just remember after you receive the machine you will also have to invest in a backing plate as well as pads. Not sure what your polish line-up consists of but you also may need to buy polishes as well; all depending on what you are going to use the machine for. Polishing defects or just waxing?
 
Check into what it would cost to rent a PC for a few hours, or borrow one from a friend, if possible. You'll still need pads. Pick up the LC CCS in 4" or 5" with the 3.5" backing plate. If yo don't like the PC, the pads still work with rotary. For that money, I think you can do better on a rotary.
 
One mistake with that rotary and you'll be spending WAY more than you budget to pay a pro to correct it or repaint the damage. IMO save a little money and do it right.
 
Thanks guys, I'm definitely saving the 30+ bucks and getting a new PC 7424 along with the backing plate and pads.



Yes I'll definitely be using Polish to get swirl marks and paint defects and also for the cleaner/wax.



I was planning on a full detail on both cars... they are white btw with :



1) Full Shampoo and Clay (Meguiars)



After the shampoo I'm gonna get into some cleaner (Sonus line or KAIO) and examine the paint.



I have seen some swirl marks but I already have a good fluorescent light on my garage to thoroughly examine the full paint for all kind of damage.



After that it will definitely be some swirl mark remover and starting out slowly and building up until everything is gone and then sealing it with Klasse Sealant or P21S.



Thanks for the quick responses guy
 
You must log in or register to reply here.
Back
Top