Innovative Detailing
New member
I wanted to share the photos and detailing procedures involved in making this ‘Torched” ZR1 shine and sparkle better than it did when it rolled off the assembly line.
My client ordered a 2010 ZR1 way back in August of 2009 from Les Stanford Chevrolet with Museum delivery option. He had the VIN in hand and was ready to leave for Bowling Green in a couple of weeks. One week before the TPW week he changed his mind and decided to buy a 2010 GT3 instead. Ultimately he decided that the GT3 was not the one for him, and was reunited with the original ZR1 he had ordered in Aug 2009.
Before his purchase it sat for months, covered and only shown on several occasions, upon my initial inspection it looked like it had been wiped down many times with inferior techniques. It also had signs of RDS (Random Deep Scratches) and some abrasion marks from being covered either in storage or in transport. But beneath it all was a jewel just waiting to be finessed for its new owner.
My client and I had spoke several times in which I got a very clear understanding of how meticulous he was and what his expectations were. I then packed it up on a very cold rainy day to drive out to VV and perform my correction work and detailing……
Here are some photos of the ZR1 upon my initial inspection…
Some shots of the CF that was opaque and dull from cover abrasion and lack of TLC
Even the wheels lacked that sparkle and were stained and dull
Here the prep begins with a thorough bath and cleaning with Poly's Clear Tech Detailing Fluid.
After drying the vehicle with an SM Arnold Water Sprite all the decals are meticulously removed so the owner can save them.
A fresh piece of Clay Magic formed into a round little tortilla ready for the claying step
Claying begins and is done on all surfaces starting on the tops leaving the lowers for last. Even the lights, wheels and polycarbonate hood cover get a once over.
Wheels get detailed and polished, all the facets get Adams Metal Polish.
Wheel barrels and calipers are also left spotless.
Some compound I noticed the factory left in the rear intake.
Now the fun begins with my PCXP and M105 with a LC 7/8 Cyan Hydro Pad for the moderate defects, But first I make sure all vulnerable moldings get masked properly.
I then correct each panel one at a time using halogen lights and a Brinkman Swirl Finder hand held light.
Inspecting the panels using my lights....and Greg's massive display of lights as well.
Now that's how CF should pop......
Engine compartment gets a nice detailing as well.
cont....
My client ordered a 2010 ZR1 way back in August of 2009 from Les Stanford Chevrolet with Museum delivery option. He had the VIN in hand and was ready to leave for Bowling Green in a couple of weeks. One week before the TPW week he changed his mind and decided to buy a 2010 GT3 instead. Ultimately he decided that the GT3 was not the one for him, and was reunited with the original ZR1 he had ordered in Aug 2009.
Before his purchase it sat for months, covered and only shown on several occasions, upon my initial inspection it looked like it had been wiped down many times with inferior techniques. It also had signs of RDS (Random Deep Scratches) and some abrasion marks from being covered either in storage or in transport. But beneath it all was a jewel just waiting to be finessed for its new owner.
My client and I had spoke several times in which I got a very clear understanding of how meticulous he was and what his expectations were. I then packed it up on a very cold rainy day to drive out to VV and perform my correction work and detailing……
Here are some photos of the ZR1 upon my initial inspection…
Some shots of the CF that was opaque and dull from cover abrasion and lack of TLC
Even the wheels lacked that sparkle and were stained and dull
Here the prep begins with a thorough bath and cleaning with Poly's Clear Tech Detailing Fluid.
After drying the vehicle with an SM Arnold Water Sprite all the decals are meticulously removed so the owner can save them.
A fresh piece of Clay Magic formed into a round little tortilla ready for the claying step
Claying begins and is done on all surfaces starting on the tops leaving the lowers for last. Even the lights, wheels and polycarbonate hood cover get a once over.
Wheels get detailed and polished, all the facets get Adams Metal Polish.
Wheel barrels and calipers are also left spotless.
Some compound I noticed the factory left in the rear intake.
Now the fun begins with my PCXP and M105 with a LC 7/8 Cyan Hydro Pad for the moderate defects, But first I make sure all vulnerable moldings get masked properly.
I then correct each panel one at a time using halogen lights and a Brinkman Swirl Finder hand held light.
Inspecting the panels using my lights....and Greg's massive display of lights as well.
Now that's how CF should pop......
Engine compartment gets a nice detailing as well.
cont....
thanks for the tip