Search results

I bought the sample kit a couple years ago and decided to try it (being using Optimum Spray). Upon opening box, etc. I noticed what appeared to be a 'hardened line' of product that had formed inside the bottle where it had been lying on its side. (I scraped it with a toothpick) Is the...

I didn't see it listed on the Compatibilty chart. I have seen a few posts (from searching) but none definitive enough. Just want to verify. I'm fairly sure it's H2O. Also, this is the prior version of Optimum. thanks

Applied over OPS. It was a little tough to see how much had been applied. I could see it flash somewhat. Sometimes within a minute and some after 15 minutes. After about an hour or so I could see 1 or 2 small areas of residue, dust, - not sure how to describe. I'll assume this was too much...

I just received my Poorboy's Wheel Sealant. The consistency is basically 1/2 paste - 1/2 liquid with some minor product separation. I don't think it's the heat (only 80 degrees) because my Natty's Blue was just fine. 2 hours later no change. Is this normal ? I was expecting a normal paste wax...

Just a quick review. FMJ shampoo - comparing to Gold Class and Pinnacle. About the same slickness but longer lasting suds. I could 'spray' into the bucket and generate more suds very easily (3 times) whereas Gold Class was only good for 1 or maybe 2. Pinnacle never impressed me for its cost...

I applied FMJ on top of WG (on top of UPP on top of SG). It reminded me of WG in terms of application. It didn't spread as easy as UPP - although still easy. In 10 minutes it was ready to remove. It came off extremely easy. More so than WG or UPP. The finish was more like WG than UPP - not quite...

Is FP2 basically the equal of SSR1 in terms of abrasiveness ? Thanks

What's the drying time (not cure) with FMJ ? and what's a good base ? AIO ? Thanks

I've used both UPP and WG and was wondering how they compare to FMJ - for anyone who has used all three. IMO - UPP is very slick and easy to remove. WG is a bit less slick and a bit less 'oily' as well and just as easy to remove. WG looks a little more like a carnuba. But I like both equally...

SSR2.5 is somewhat equal to DACP # 83 ? If SSR2.5 is used SSR1 can be used to clean up any minor marring and SSR2 isn't really needed ? SSR2.5 basically can take the place of SSR2 since SSR2.5 has diminishing abrasives like DACP ? Thanks

Anyone ever mix this two (i.e. similiar to SG plus Sonus Spritz) ? Thanks

Just some comments on the tire gels I've been using lately. Meg. Endurance - longest lasting, a bit thick to spread and needs a good buffing to get 'level'. EImann Fabrik - shortest lasting, thin, must buff thoroughly to prevent sling. I buff this out with an old cotton app. pad. - helps absorb...

Just some comments on the tire gels I've been using lately. Meg. Endurance - longest lasting, a bit thick to spread and needs a good buffing to get 'level'. EImann Fabrik - shortest lasting, thin, must buff thoroughly to prevent sling. I buff this out with an old cotton app. pad. - helps...

Just a couple of quick comments on the Handi-Grip Applicator and using a terry pad to apply tire dressing. I tried out the Handi-Grip Applicator (shop Autopia - I beleive they're Viking) yesterday to apply a coat of UPP. First, it is very comfortable. Second, the pad lays flat while applying...

Anyone use these ? Thanks

...or more specifically, what should you NOT apply NXT on top off ? (i.e. i'm assuming AIO is OK but what about SMR's such as 3M or #82,83) Thanks

Anyone use these ? $1.95 a pad - China maybe. I plan to call Monday to ask.

Winter Coat: SSR1 - worked about like 3M SMR but came off a little easier. AIO - same as always SG X 3 - I put one coat on waiting 6 hours to buff off, the 2nd and 3rd I used the wipe-wipe off(SG 2.0) - 24 hours between. I've put on about a dozen or more coats (over last couple of...

I’d like to clear up some questions I have regarding polish/compound usage. I’ve searched extensively but still have a couple of questions. 1) Does this progression of products (most abrasive to least) to use in treating scratches, swirls, etc. seem logical?: SSR3 or 3M RC 39002, then...

How do these products compare ? I'm thinking SSR2 is a little less abrasive than DACP and PI II FC. And DACP is a little less abrasive than PI II FC. Also, I think SSR2 and DACP both have diminishing abrasives but PI II FC does not. Thanks for any input.