Recent content by bdaly84

I have been wondering if anyone can shed some light on how to link certain foundations on a website. I want to link up three foundations through my website...that I donate to...but I am not sure where to begin. Any help is appreciated.

One thing is for sure, my phone is definalty not ringing like it always has. Even my regulars have cut back from seeing them every two weeks to almost just once a month. Even the "well off customers" have dropped back slightly. Anyone else feeling the reduction in work? I have never...

Well now that I we are all paying $4.00/gal for gas, I am looking to lighten my load in my truck to try to save some MPG's. I currently carry most of supplies/ equipment except for the extractor (only take when needed). However, I am still carrying around 200-250lbs of supplies/equipment. I...

I know that 3M Ultrafina is supposed to used with a rotary. I was just wondering if anyone has tried it with any DA machines? If so...what pad choice and what were the results. Thanks:cool:

I am getting ready to perform a full exterior job on a new customer with a 1987 Porsche 928S with the original single stage paint on it. This will be my first 20year original paint Porsche. He wants as close to 100% correction as possible. I have seen alot of guys use the Megs 80 series stuff...

Trying to switch to Pinnacle for my "hand-applied" regulars, I call them. Right now I have been using PB Nattys (blue and red). I am almost out and just need to replenish. I have been wanted to try Pinnacle Soverign. However, from looking at their site, which nuba is better....the...

I just purchased a Foam Gun and DP extreme wash. My primary washing is and has been with ONR. However, on new customer vehicles, they usually have aweful exteriors as far as mud and dirt. So, I am going to try the Foam Gun first, just rinse it off, then ONR. Has anyone tried this combo...

Today I was at one of my regulars and using my cyclo with orange LC pads and OP. I noticed towards the end of using this combo, the machine was boggin down when I started it up....not even on a panel yet....and it was boggin. Like it was trying to get up to speed. After about 60 or so seconds...

I am thinking of getting into mobile Paint Chip and Scratch repair. I have seen some kits through various vendors and I was interested to know if any of you have looked into these systems? Rightlook, Detail King, Dr. Color Chip etc. I know about and have used the Langka system, but I am...

I only use a tiny bit of detergent in my "towel loads" when I clean my towels/MF's. Problem is, sometimes they seem cleaner than other times, maybe its just me. I typically use Tide (orignal, no additives) and the hot water setting. Just trying to gather some info on what you gentleman use...

I was adjusting my new rockers on my Vette the other night and I get some oil spilled on the headers. I was adjusting them while the car was running, so while getting burned with hot oil, I really could not wipe up the the oil that spilled on the headers. They are ceramic coated Hedmans and...

Has any Cyclo user tried the wool pads they make for it?? Sometimes the yellows just aren't enough. If so...what polish or compound did you use?

I am getting some polo-type shirts made for use as work shirts. Should I have the logo just on the front breast or also on the back, kinda like a T-shirt? I have seen both ways. I like both, but just curious as to what everyone else is using? I have t-shirts now, but they are getting ragged...

I have a 21' Regal Boat this coming weekend and I am doing a full detail on it. I ordered the gelcoat polishes, sealants, and cleaners, however, I was thinking of using ONR, but now I am leaning towards a convential wash/soap. The boat is mildly ox'd and it will require polishing. There...

Just like the title says. Just trying to get some input. Thanks:xyxthumbs