California Water Blade

TheSopranos16

TheSopranos16

New member
What does everyone think of this product? I picked one up a few weeks ago...I think it works great and all but I'm not sure if its putting microfine scratches into my paint. I think its great to use to just go over the car and get most of the water off, then go back and fnish up with a towel. But, if its going to put marks in the finish, its out the window! So what does everyone think?
 
I think you'll find those who love it and those who would never let one touch their car. I've been using the CWB for a few years with good success.

The key to avoiding adding scratches is simple - just make sure it's clean before running it over the surface. I hit both sides with a stream of water from the hose before using. Some guys will spray some QD on it.
 
Aloha bro!

There is a lot of water blades out there. I like the California one the best. It has a wide handle for easy use while wet, and it has a unique "T" flap to ease over curves without a lot of pressure.

As far as scratchs go, in 2+ years of using it, no scratchs none at all. Just make sure you rinse your car well.

But whatever, if you like it go with it. Thats what I always say.

A hui hou
"have a nice day"
 
Personally, I don't like using the CWB on paint. (works nice on windows though).

However, if one wants to try the CWB, here's what I would recommend................. Make sure that you do absolutely "perfect" car washes to remove "ALL" the dirt before using the CWB. Next, make sure that you leave lots of water on the paint surface to allow the CWB to glide over the surface.

In the end, I still think a good "flood rinse" of the vehicle, and a high quality WW towel make a better drying process.
 
CWB

Love this thing!!

I keep a small amount of water running out of a hose elevated next to the car for rinsing the blade after each panel.

I always check the blade often and wipe it off as well with a clean MF to remove any micro paricles.

Some of us use leaf blowers, WW towels etc.

I still use a WW with the blade to quickly pick-up any water in hard to reach areas or heavy curve areas that the blade didn't fully get.

Regards,
Deanski
 
I use it when I wash the truck but I seldom wash it. I dust daily and S&W almost daily.
 
Boss_429 said:
Personally, I don't like using the CWB on paint. (works nice on windows though).

However, if one wants to try the CWB, here's what I would recommend................. Make sure that you do absolutely "perfect" car washes to remove "ALL" the dirt before using the CWB. Next, make sure that you leave lots of water on the paint surface to allow the CWB to glide over the surface.

In the end, I still think a good "flood rinse" of the vehicle, and a high quality WW towel make a better drying process.
Click to expand...

My thoughts exactly. If a car is properly protected and rinsed in the correct way, there is very little water left on the paint. The CWB would actually be slower for me. I just can't justify the risk.
 
Windows only for me. Already marred paint with it once, can't figure out how, EVERYTHING was totally clean.
 
I used a CWB for a while in conjunction with an Absorber. I never had a problem with either one, but I was always very careful about rinsing and swiping the blade clean with my fingers. Once I discovered waffle weave MF towels, the CWB and Absorber were put on the back burner.
 
Well if i would have seen this post three days ago i would have said i loved the cwb, but the other day i managed to put a few little scrates on the hood of a very nice BLACk car and i didnt even notice, the owner called me about two hours later and mentioned it too me , so ill have a little extra work to do next week, hope the scrathes come out, or else im screwed. I would recomend using the blade on window and white and silver paint only, its just not worth the extra effort of removing scrates from a hood. IMO,
 
You must log in or register to reply here.
Back
Top